4-Post Rubber Isolated Bar Mounts, M12 interface for Luxon Gen3 and Xtrig Clamps
Our lightweight 4-post bar mounts eliminate twisting due to small crashes and tip-overs without sacrificing vibration absorbtion like a solid mount would. Four sets of bushings absorb hard hits and track roughness without compromising steering precision. Three different rubber bushing sets (soft, medium, and firm) are included to fine tune the feel.
Our mounts are low profile at only 21 mm in height (bottom of bar to top of triple clamp), but we offer this bar riser kit to raise them up 5, 10, or 15 mm. Handlebar size is available in both standard 1 1/8" or 36 mm (Fits Renthal FB36 bars only) sizes.
- $189.95 (Steel Bar Clamp Bolts)
Product Description, Fitment, Information, and Details
M12 Direct Bolt-On Interface:
The M12 interface on a Luxon Gen3 triple clamp (click to enlarge)
The M12 interface is a recessed slot on the top triple clamp, 26 mm wide, with three 12 mm threaded holes per side. The bar mounts sit in these slots and bolt directly to the triple clamp with an M12 bolt.
Fitment:
These mounts fit Luxon Gen3, Gen3 Pro, and many Xtrig triple clamps. They do NOT fit stock clamps or other aftermarket clamps. Our mounts fit most bikes without issue. In some cases, you may need to trim plastic brackets or relocate hour meters or accessories to allow clearance in the extreme mounting positions (for example: front hole, bars away from the rider). Always check for full clearance after installation and before riding.
Bar Size
Luxon 1 1/8" bar mounts fit standard 1 1/8" (28.6 mm) handlebars (sometimes called fatbars) and 36 mm mounts fit the Renthal FB36 bars (36 mm). These are NOT the same as fatbars, they have a much larger clamping diameter. If you're not sure, you almost certainly want the 1 1/8" bar size!
We do not offer bar mounts to fit the old 7/8" size handlebars. BRP and other aftermarket companies offer adapter bushings to fit the 7/8" bar diameter in standard 1 1/8" mounts if necessary.
Our M12 mounts fit Luxon Gen3, Gen3 Pro, and most Xtrig triple clamps. If in doubt, please double check that your triple clamps have an M12 interface as explained above.
- Luxon
- All Gen3 Triple Clamps
- All Gen3 Pro Triple Clamps
- Xtrig
- All modern Xtrig Triple Clamps
These mounts have a height of 21 mm (bottom of bar to top of triple clamp) and a 3.75 mm offset (7.5 mm of bar position change when flipping the mounts around). An optional spacer kit is available (allows 21 mm, 26 mm, 31 mm, and 36 mm heights).
Includes rubber isolated lower bar mounts, rubber bushings, upper bar clamps, high-strength steel mount and clamp bolts (titanium clamp bolts are an optional upgrade), anti-seize, and instructions.
Three different hardness levels of rubber bushings are included at no additional cost. Soft (green) is for lighter riders, vet riders, or those with wrist injuries. Medium (yellow) is recommended for most off-road and motocross use, and hard (red) is recommended for aggressive motocross use and faster riders.
Bushings will "break in" on the first ride and become a little softer than when first installed. Like all rubber bushings, these are wear items and will eventually break down and need replacing. Softer bushings will need to be replaced more often than harder bushings. Replacement bushings are available for a reasonable cost.
Installation video and instructions can be found on our customer page.
| Luxon Part# | LUX-GEN-SS-A0011-118,FB36 |
|---|---|
| Luxon Description | BAR MOUNTS, 4-POST RUBBER, M12 |
| Weight, 1 1/8" | 367 g, 0.81 lbs |
| Weight, 36 mm | 399 g, 0.88 lbs |
| Weight (1 1/8") | 347 g, 0.76 lbs (with Ti bolts) |
| Weight (36 mm) | 379 g, 0.84 lbs (with Ti bolts) |
| Xtrig PHDS Weight | 506 g, 1.12 lbs |
| Stock Weight | N/A |