4-Post Rubber Isolated Bar Mounts, Yamaha 2-Stroke Interface
Upgrade your harsh solid bar mounts with our 4-Post rubber mounts. These lightweight bar mounts significantly reduce vibration, eliminate twisting in small crashes and tip-overs, and absorb hard hits and roughness without compromising steering precision. Three different bushing sets (soft, medium, and firm) are included to fine tune feel.
These mounts fit Yamaha 2-stroke motorcycles with triple clamps using direct bolt on bar mounts (12 mm unthreaded hole). Handlebar size is available in both standard 1 1/8" or 36 mm sizes. Please read the Fitment tab below for bike and bar mount specifics.
- $189.95
Product Description, Fitment, Information, and Details
Yamaha Two-Stroke Interface:
The Yamaha Two-Stroke interface on a stock clamp (click to enlarge)
The Yamaha Two-Stroke interface is a simple 12 mm thru hole in the top clamp with a thickness of 25 mm.
Fitment:
These mounts fit stock Yamaha triple clamps with the M12 thru-hole interface, which includes most all modern Yamaha 2-stroke motocross and off-road models. These mounts do NOT fit the modern four-stroke models with rubber cones. We have four stroke cone mounts available here.
Depending on the installation type, make and model of bike, bar mount position, etc., you may need to lightly trim plastic brackets and/or relocate hour meters or accessories to allow clearance for these bar mounts in some mount positions (typically not an issue on motocross bike installations). Always check for full clearance after installation and before riding.
Bar Size
Luxon 1 1/8" bar mounts fit standard 1 1/8" (28.6 mm) handlebars (sometimes called fatbars) and 36 mm mounts fit the Renthal FB36 bars (36 mm). These are NOT the same as fatbars, they have a much larger clamping diameter. If you're not sure, you almost certainly want the 1 1/8" bar size!
We do not offer bar mounts to fit the old 7/8" size handlebars. BRP and other aftermarket companies offer adapter bushings to fit the 7/8" bar diameter in standard 1 1/8" mounts if necessary.
These mounts fit stock Yamaha 2-stroke triple clamps, and may fit older 4-stroke triple clamps and many other clamps with a simple 12 mm unthreaded hole (not ones with rubber cones). The list below includes bikes that our mounts should fit; there may be more bikes not listed that our mounts will fit too. While the list is accurate as far as we know, mistakes can happen! Please double check that your bike has an Yamaha two-stroke interface as exlained above.
- Yamaha
- YAMAHA YZ125 2006-2026
- YAMAHA YZ125X 2006-2026
- YAMAHA YZ250 2006-2026
- YAMAHA YZ250X 2006-2026
- 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026
The mounts are the stock offset of 5 mm (10 mm of bar position change when flipping the mounts around). Height is increased by only 2.5 mm (25.5 mm high, bottom of bar to top of triple clamp). Includes rubber isolated lower bar mounts, rubber bushings, upper bar clamps, high-strength steel mount and clamp bolts, anti-seize, and instructions.
Three different hardness levels of rubber bushings are included at no additional cost. Soft (green) is for lighter riders, vet riders, or those with wrist injuries. Medium (yellow) is recommended for most off-road and motocross use, and hard (red) is recommended for aggressive motocross use and faster riders.
Bushings will "break in" on the first ride and become a little softer than when first installed. Like all rubber bushings, these are wear items and will eventually break down and need replacing. Softer bushings will need to be replaced more often than harder bushings. Replacement bushings are available for a reasonable cost.
Installation video and instructions can be found on our customer page.
| Luxon Part# | LUX-YAM-SS-A0022-118,FB36 |
|---|---|
| Luxon Description | BAR MOUNTS, 4-POST RUBBER, YAMAHA 2-STROKE |
| Weight, 1 1/8" | 378 g, 0.83 lbs |
| Weight, 36 mm | 410 g, 0.90 lbs |
| Stock Weight | 410 g, 0.90 lbs |