4-Post Rubber Isolated Bar Mounts, Ducati Cone Interface
Our lightweight 4-post bar mounts eliminate twisting due to small crashes and tip-overs without sacrificing vibration absorbtion like a solid mount would. Four sets of bushings absorb hard hits and track roughness without compromising steering precision. Three different rubber bushing sets (soft, medium, and firm) are included to fine tune the feel.
These bar mounts fit the Ducati DESMO 450 MX motorcycle using a rubber cone interface; see the fitment tab below for specifics. They will work in both the forward and back triple clamp mount hole locations and have the same bar position geometry as stock (height and offset). Handlebar size is available in both standard 1 1/8" or 36 mm (Fits Renthal FB36 bars only) sizes.
- $239.95
Product Description, Fitment, Information, and Details
Ducati Cone Interface:
The Ducati Cone interface on a stock clamp (click to enlarge)
The Ducati Cone interface is a tapered cone shaped hole on the top and bottom of the triple clamp (a cross section would look like an hour glass). Newer stock triple clamps have two sets of holes for position adjustment; our bar mounts fit both hole positions.
Fitment:
These mounts fit stock Ducati triple clamps with the rubber cone interface, which includes many Ducati motocross and off-road models.
Depending on the installation type, make and model of bike, bar mount position, etc., you may need to lightly trim plastic brackets and/or relocate hour meters or accessories to allow clearance for these bar mounts in some mount positions (typically not an issue on motocross bike installations). Always check for full clearance after installation and before riding.
Bar Size
Luxon 1 1/8" bar mounts fit standard 1 1/8" (28.6 mm) handlebars (sometimes called fatbars) and 36 mm mounts fit the Renthal FB36 bars (36 mm). These are NOT the same as fatbars, they have a much larger clamping diameter. If you're not sure, you almost certainly want the 1 1/8" bar size!
We do not offer bar mounts to fit the old 7/8" size handlebars. BRP and other aftermarket companies offer adapter bushings to fit the 7/8" bar diameter in standard 1 1/8" mounts if necessary.
Our Ducati Cone mounts fit many Ducati bikes. The list below includes bikes that our mounts should fit; there may be more bikes not listed that our mounts will fit too. While the list is accurate as far as we know, mistakes can happen! Please double check that your bike has an Ducati Cone interface as exlained above.
- Ducati
- DUCATI DESMO450 MX 2026
- DUCATI DESMO450 EDX 2026
- DUCATI DESMO250 MX 2027
- 2026 2027
The mounts will work in both the forward and back triple clamp mount hole locations and are the stock offset (8 mm of bar position change when flipping the mounts around). Height is the same as stock (28 mm high, bottom of bar to top of triple clamp). Includes rubber isolated lower bar mounts, rubber bushings, upper bar clamps, high-strength steel mount and clamp bolts, anti-seize, and instructions.
Three different hardness levels of rubber bushings are included at no additional cost. Soft (green) is for lighter riders, vet riders, or those with wrist injuries. Medium (yellow) is recommended for most off-road and motocross use, and hard (red) is recommended for aggressive motocross use and faster riders.
Bushings will "break in" on the first ride and become a little softer than when first installed. Like all rubber bushings, these are wear items and will eventually break down and need replacing. Softer bushings will need to be replaced more often than harder bushings. Replacement bushings are available for a reasonable cost.
Installation video and instructions can be found on our customer page.
| Luxon Part# | LUX-DUC-SS-A0001-118,FB36 |
|---|---|
| Luxon Description | BAR MOUNTS, 4-POST RUBBER, DUCATI CONE |
| Weight, 1 1/8" | 429 g, 0.95 lbs |
| Weight, 36 mm | 461 g, 1.02 lbs |
| Stock Weight (2026 Model) | 354 g, 0.78 lbs |