Nexus Bar Mounts, Suzuki Cone Interface
Nexus is the ultimate, comfort oriented, high-performance bar mount. These mounts fully isolate the handlebar from the triple clamp with highly developed elastomer sets, absorbing roughness and vibration from the track or trail, without a loss of steering precision, and eliminating twisting in small crashes and tip-overs.
This mount is a must for off-road and enduro, but also works great for motocross, vet riders, and riders with hand and wrist injuries. The unique, patent pending design, is much lighter, more versatile, simpler, and less expensive than competing products. Three bushing sets (soft, medium, and firm) are included to tune the feel.
These bar mounts fit stock Suzuki triple clamps only. Please read below for exact fitment details.
- $359.95
| Mounts | Status | ETA |
|---|---|---|
| Nexus Suzuki Cone | In Stock | Now |
Product Description, Fitment, Information, and Details
Suzuki Cone Interface:
The Suzuki Cone interface on a stock clamp (click to enlarge)
The Suzuki Cone interface is a tapered cone shaped hole on the top and bottom of the triple clamp (a cross section would look like an hour glass).
Bar Size
The Nexus bar mounts fit standard 1 1/8" handlebars only (the most common size). Sorry, we do not offer the Nexus bar mounts in the FB36 (36 mm) size or the older 7/8" bar size.
Bar Position
Nexus mounts are the stock Suzuki height of 30 mm (bottom of bar to top of triple clamp) and offset (5 mm of bar position change when flipping the mounts around).
Bike Fitment:
These mounts fit stock Suzuki triple clamps with the rubber cone interface, which includes many Suzuki motocross and off-road models. Our mounts fit most bikes without issue, but in some cases, you may need to trim plastic brackets or relocate hour meters or accessories to allow clearance in the extreme mounting positions. Always check for full clearance after installation and before riding.
Most standard bar pads will fit with some trimming around the bar mount area. A Dremel tool with a sanding drum makes this easy, but a razor blade can be used as well.
An alignment tool is available here to ease installation and ensure correct alignment of the bar mount bases in the triple clamp. This tool is NOT required for installation, but makes the process a little easier and foolproof.
Our Suzuki Cone mounts fit many Suzuki bikes. The list below includes bikes that our mounts should fit; there may be more bikes not listed that our mounts will fit too. While the list is accurate as far as we know, mistakes can happen! Please double check that your bike has an Suzuki Cone interface as exlained above.
- Suzuki
- SUZUKI RM-Z 250 2007-2026
- SUZUKI RM-Z 450 2005-2026
- 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023, 2024, 2025, 2026
Our patent pending Nexus bar mounts are lighter, simpler, more versatile, and less expensive than competing products and setups. These mounts are 25% lighter and nearly 20% less expensive than the comparable XC Gear Mako360 bar mount, but have increased steering precision and mounting versatility.
When compared to a Flexx handlebar setup, the Nexus bar mounts save nearly two pounds (832 g) at 11% lower cost (solid bar mounts with Flexx bars vs. Nexus bar mounts with Pro Taper Evo bars).
The Nexus bar mount system includes rubber bushings, bar clamps, bases, caps, high-strength steel mount and pinch bolts, cones, and anti-seize.
Three different hardness levels of bushings are included at no additional cost. Bushing hardness is a compromise between comfort (soft) and steering precision (firm). Like all rubber bushings, these are wear items and will eventually break down and need replacing. Softer bushings will need to be replaced more often than harder bushings and are more susceptible to crash damage. Replacement bushings are available for a reasonable cost.
| Soft (Green) | Medium (Yellow) | Firm (Red) |
|---|---|---|
| Soft bushings are for less aggressive or lighter weight riders. | Medium Bushings are a good starting point and will be preferred by most novice or vet riders. | Firm bushings are a good choice for faster and more agressive riders |
| It is also possible to mix a harder bushing on top with a softer bushing on the bottom (do not mix softer on top than bottom). | ||
Installation instructions can be found on our customer page.
| Luxon Part# | LUX-SUZ-SS-A0050 |
|---|---|
| Luxon Description | NEXUS BAR MOUNTS, SUZUKI CONE |
| Weight | 576 g, 1.27 lbs |
| Stock Weight (2026 Model) | 486 g, 1.07 lbs |